Skip to content

Guide

Why your garage door will not close, and what you can safely check

Two single garage doors with window rows at dusk, lit by a light above them

The short answer

When a garage door starts down and goes back up, the cause is usually the photo eyes: the two small sensors near the floor on each side of the door. One has been bumped, the lens is dirty, or sunlight is hitting it. Check that both sensor lights are steady, wipe the lenses, and clear anything in the beam. If the door will not move at all, or it is crooked, or you heard a bang, stop there. That is a spring, cable or track problem and it is not safe to work on yourself.

Updated . General information for the Springfield, MO area. Prices are typical market ranges, not a quote.

Start by watching what it does

Press the wall button and watch one full attempt. What the door does tells you where to look.

What the door does and where to look
What you seeLikely causeSafe to check yourself?
Starts down, reverses, opener light blinksLikely causePhoto eyes blocked or out of lineSafe to check yourself?Yes
Goes down, touches the floor, comes back upLikely causeClose limit or force settingSafe to check yourself?Yes, with the manual
Closes only if you hold the wall buttonLikely causePhoto eyesSafe to check yourself?Yes
Stops partway at the same spot each timeLikely causeSomething binding in the trackSafe to check yourself?Look, do not force
Remote does nothing, wall button worksLikely causeRemote battery or lock modeSafe to check yourself?Yes
Nothing happens at allLikely causePower, GFCI, or a dead openerSafe to check yourself?Check power only
One side lower, door crookedLikely causeCable off or roller outSafe to check yourself?No. Stop.
Loud bang, door very heavyLikely causeBroken springSafe to check yourself?No. Stop.

Check 1: the photo eyes

Every opener made since 1993 has a pair of photo eyes mounted no more than six inches above the floor, one on each side of the opening. One sends an invisible beam and the other receives it. If anything breaks the beam while the door is closing, the opener reverses. This one feature has prevented a great many injuries to children and pets, and it is also the most common reason a door refuses to close.

Diagram of the two photo eye sensors at the bottom of a garage door opening, mounted no more than 6 inches above the floor, with the beam running between themInvisible beam6 in.or lessSending eyeReceiving eyeIf anything breaks the beam while the door is closing, the opener reverses.Door opening, seen from inside
The two photo eyes face each other across the opening, six inches or less above the floor.
  1. Look at the small light on each sensor. Both should be on and steady. If one is off or flickering, that sensor cannot see the other.
  2. Clear the path. A broom, a trash can, a spider web or a leaf stuck to the lens is enough.
  3. Wipe both lenses with a dry cloth.
  4. If a light still flickers, loosen the wing nut on that sensor's bracket and turn the sensor by hand until the light goes steady. Tighten it there.
  5. Follow the thin wire from each sensor back toward the opener. Look for a staple through it or a spot where it has been snagged or chewed.

Sun in the eye. On winter afternoons the low sun can shine straight into the receiving sensor and blind it, most often on west-facing garages. If the door closes fine at night and refuses at 4 p.m., that is the cause. Shading the sensor with a short cardboard tube, or swapping the two sensors side to side, usually cures it.

Holding the wall button down overrides the photo eyes on most openers. It is fine for getting the door shut tonight. Do not make a habit of it.

Check 2: the track

Look up both vertical tracks for anything in the way: a rag, a toy, a bracket that has bent inward. Check the horizontal tracks too. Wipe the inside of the tracks if they are gummy. Do not grease them.

If you see a roller sitting outside the track, or the track is visibly bent, stop. That is off-track repair.

Check 3: the opener's limits

If the door travels all the way down, touches the floor and then pops back open, the opener thinks it hit an obstacle. Its close limit is set a little too far, so it pushes into the slab and reverses. This drifts with the seasons as the slab and the seal move. The limit is adjusted with a screw or a pair of buttons on the opener body. The steps are in the opener's manual and on the label under the light cover. Adjust in small steps.

Leave the force setting alone unless the manual tells you otherwise. Turning the force up so the door closes is how safety reversal gets defeated.

Check 4: the simple electrical things

  • Lock mode. Many wall consoles have a lock button that disables the remotes. A blinking light on the console usually means it is on. Hold the lock button for a few seconds.
  • Remote battery. If the wall button works and the remote does not, start here.
  • GFCI. Garage outlets are often on a ground-fault circuit that trips in damp weather. Find the outlet with the reset button, which may be on another wall or in a bathroom, and press it.
  • The release cord. If the opener runs and the door stays, the trolley is disconnected. Pull the red cord back toward the opener and run the opener until it clicks in.

In winter: frozen to the floor

This one is a door that will not open, but it belongs here because of what people do next. If the seal has frozen to the slab, the opener pulls, senses the resistance and stops. Pressing the button again and again can strip the opener gear or tear the seal out. Pull the release, free the seal by hand or with warm water, then reconnect.

Where to stop

If the door is stuck open overnight and that is a security worry, a tech can usually get it closed and secured even if the full repair waits for a part. Say so when you send the form.

Questions

Why does my garage door go down a foot and come back up?

Most often the photo eyes. Check that both sensor lights are steady, the lenses are clean and nothing crosses the beam. If the door only does it in cold weather, stiff rollers or a tired spring may be making the opener think it hit something.

Can I bypass the garage door sensors?

Holding the wall button closes the door past the sensors on most openers, and that is the only bypass you should use. Disconnecting or taping the sensors together defeats the feature that keeps the door from closing on a child or a pet.

Why will my garage door not close when it is sunny?

Low sun is shining into the receiving photo eye. Shade that sensor with a small tube or visor, or have the sensors swapped to opposite sides.

The door closes and then immediately reopens. What is wrong?

The close limit is set slightly too far, so the opener presses the door into the floor and reads it as an obstacle. Adjust the close limit in small steps, following the opener's manual.

Get a price for your door

Send the form and your request goes to a local garage door technician, who follows up with you directly.

  • Free to send, and no obligation to book
  • Goes to a technician who works in your town
  • Ask for the full price before any work starts
  • Repairs, openers and new doors

Request a quote

Tell us what the door is doing. A local garage door technician will follow up with you about the repair and the price.

It costs nothing to ask, and you decide whether to book once you have a price.

Get a free quote