Skip to content

Service

Garage door spring replacement in Springfield, MO

You heard a bang like something heavy fell off a shelf. Now the opener strains, lifts the door a few inches and quits. Look at the bar above the door. If the spring on it has a gap of an inch or two in the coils, that is your answer.

A broken spring is the most common garage door repair in the Springfield area, and one of the quicker ones for a tech with the right spring on the truck. Send the form and a local technician will follow up with you.

Dark green raised-panel garage door with snow falling in front of it

What the spring does

The opener does not lift your door. The springs do. A double steel door weighs somewhere around 150 to 250 pounds, and the springs are wound to offset almost all of it. A door in good balance can be lifted with one hand. The opener only has to guide it.

When a spring breaks, the opener is suddenly trying to lift the full weight. Most will not. The ones that try can strip their drive gear or bend the top section of the door, which turns one repair into two. That is why the first advice is always the same: stop pressing the button.

Diagram of a sectional garage door seen from inside the garage, with the torsion spring, cable drums, lift cables, tracks, rollers, bottom brackets, opener rail and photo eyes labeledTorsion springCable drumLift cableRollerTrackBottombracketPhoto eyeOpener railView from inside the garage, door closedYellow parts are under spring tension. Leave them to a technician.
The parts a spring job touches: the spring, the drums at each end of the shaft, the lift cables and the bottom brackets.

How long springs last, and why they break in January

Standard residential springs are rated for about 10,000 cycles. One cycle is the door going up and coming back down. A household that uses the garage as the front door can run six or eight cycles a day, which puts a standard spring at four or five years. Two cycles a day stretches that past a decade.

Steel gets more brittle in the cold, so a spring near the end of its life tends to let go on a cold morning. Springfield's average January low is about 24 degrees, and the first hard snap of the winter is when the calls stack up. Humidity does its part the rest of the year. Rust on the coils adds friction and shortens the life of the steel.

More on spring types and cycle ratings in torsion vs extension springs.

What a proper spring job includes

  • Springs matched to the door. Springs are sized by wire thickness, inside diameter and length, and the right size depends on the weight and height of your door. A tech should measure the old spring or weigh the door, not guess.
  • Both springs replaced on a two-spring door. They were installed together and have done the same number of cycles. The second one is not far behind.
  • A look at the cables, drums, end bearings and center bearing while the tension is off. A frayed cable is cheap to replace during a spring job and expensive to ignore.
  • A balance test at the end. With the opener disconnected, the door should stay put when it is left half open. If it drifts down or creeps up, the spring is the wrong size or needs adjusting.
  • A check of the opener's travel and force settings, since they were set for the old spring.

What it typically costs

Spring replacement, typical ranges
JobTypical range
Torsion spring, one-car doorTypical range$150 to $350
Pair of torsion springs, 16x7 double doorTypical range$300 to $500
Extension springs, pairTypical range$120 to $200
High-cycle springs with new bearingsTypical range$600 to $750
Converting extension springs to torsionTypical range$400 to $800
General market ranges from 2025 and 2026 cost surveys and from what working techs report charging. Not a quote.

Be wary of a spring price far above these. Homeowners around the country have posted invoices of $1,500 and more for a standard spring change, usually after a low-priced tune-up coupon got a salesman in the door. Ask for the total before the tech starts, and ask what the spring's cycle rating is.

Why this is not a weekend project

A wound torsion spring holds enough energy to lift the door, and winding a new one means putting that energy in by hand with steel bars, a quarter turn at a time. If a bar slips or a set screw strips, the bar and your hand are in the way. The door industry's own safety guidance says springs, cables and bottom brackets should be adjusted only by a trained technician.

Spring replacement: questions

Can I open the door by hand with a broken spring?

With the door closed, you can pull the release and try, but you will be lifting the full weight of the door, often 150 pounds or more, and it will not stay up. Two strong adults can sometimes get a car out and prop the door with locking pliers on the track. It is safer to wait.

Should both springs be replaced if only one broke?

Yes, on a two-spring door. Both springs have the same number of cycles on them. Replacing one leaves the door out of balance and usually means a second service call within months.

How long does a spring replacement take?

A tech with the right springs on the truck usually finishes a standard residential door in about an hour. Odd sizes or heavy wood doors can mean ordering a spring.

What is a high-cycle spring?

A spring built from longer or heavier wire so it is rated for more cycles than the standard 10,000, commonly 20,000 or more. It costs more up front. It makes sense if you use the door many times a day.

Ask about spring replacement

Send the form and your request goes to a local garage door technician, who follows up with you directly.

  • Free to send, and no obligation to book
  • Goes to a technician who works in your town
  • Ask for the full price before any work starts
  • Repairs, openers and new doors

Request a quote

Tell us what the door is doing. A local garage door technician will follow up with you about the repair and the price.

It costs nothing to ask, and you decide whether to book once you have a price.

Get a free quote